View 5962R0251002HXA_2631534.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

revisions ltr description date (yr-mo-da) approved rev sheet rev sheet rev status rev of sheets sheet 1 2 3 4 5 6 7 8 9 10 11 12 13 pmic n/a prepared by steve l. duncan defense supply center columbus standard microcircuit drawing checked by michael c. jones post office box 3990 columbus, ohio 43216-5000 this drawing is available for use by all departments approved by raymond monnin microcircuit, hybrid, linear, 3.3 volt, single channel, dc-dc converter and agencies of the department of defense drawing approval date 01-11-30 amsc n/a revision level size a cage code 67268 5962-02510 sheet 1 of 13 dscc form 2233 apr 97 5962-e090-02 distribution statement a . approved for public release; distribution is unlimited.
standard microcircuit drawing size a 5962-02510 defense supply center columbus columbus, ohio 43216-5000 revision level sheet 2 dscc form 2234 apr 97 1. scope 1.1 scope . this drawing documents five product assurance cl asses as defined in paragraph 1.2.3 and mil-prf-38534. a choice of case outlines and lead finishes which are available and are reflected in the part or identifying number (pin). when available, a choice of radiation hardness a ssurance levels are reflected in the pin. 1.2 pin . the pin shall be as shown in the following example: 5962 - 02510 01 h x x ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? federal rha device device case lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) \ / (see 1.2.3) \/ drawing number 1.2.1 radiation hardness assurance (rha) designator . rha marked devices shall meet the mil-prf-38534 specified rha levels and shall be marked with the appropriate rha designator. a dash (-) indicates a non-rha device. 1.2.2 device type(s) . the device type(s) identify the circuit function as follows: device type generic number circuit function 01 mhf+283r3s/883, mhf+283r3sf/883 dc-dc converter, 8 w, 3.3 v output 02 smhf283r3s, smhf283r3sf dc-dc converter, 8 w, 3.3 v output 1.2.3 device class designator . this device class designator shall be a single letter identifying the product assurance level. all levels are defined by the requirement s of mil-prf-38534 and require qml certification as well as qualification (class h, k, and e) or qml listing (class g and d). the product assurance levels are as follows: device class device performance documentation k highest reliability class available. this level is intended for use in space applications. h standard military quality class level. this level is intended for use in applications where non-space high reliabilit y devices are required. g reduced testing version of the standard milit ary quality class. this level uses the class h screening and in-process inspections with a possible limited temperature range, manufacturer specified incoming fl ow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (group a, b, c and d). e designates devices which are based upon one of the other classes (k, h, or g) with exception(s) taken to the requirements of that class. these exception(s) must be specified in the device acquisition doc ument; therefore the acquisition document should be reviewed to ensure that the except ion(s) taken will not adversely affect system performance. d manufacturer specified quality class. q uality level is defined by the manufacturers internal, qml certified flow. this product may have a limited temperature range.
standard microcircuit drawing size a 5962-02510 defense supply center columbus columbus, ohio 43216-5000 revision level sheet 3 dscc form 2234 apr 97 1.2.4 case outline(s) . the case outline(s) are as designated in mil-std-1835 and as follows: outline letter descriptive designator terminals package style x see figure 1 8 dual-in-line z see figure 1 8 flange mount 1.2.5 lead finish . the lead finish shall be as specified in mil-prf-38534. 1.3 absolute maximum ratings . 1 / input voltage range.................................................................... -0 .5 v dc to +50 v dc power dissipation (p d ): device types 01 and 02 (non-rha) ....................................... 8 w device type 02 (rha levels l and r)..................................... 9 w output power ............................................................................. 8.23 w lead soldering temperatur e (10 seconds )................................. +300 c storage temperature range ....................................................... -65 c to +150 c 1.4 recommended operating conditions . input voltage r ange.................................................................... +16 v dc to +40 v dc case operating temperature range (t c ) .................................... -55 c to +125 c 2. applicable documents 2.1 government specification, standards, and handbooks . the following specification, standards, and handbooks form a part of this drawing to the extent specified herein. unless ot herwise specified, the issues of these documents are those liste d in the issue of the department of defense i ndex of specifications and standards (dodi ss) and supplement thereto, cited in the solicitation. specification department of defense mil-prf-38534 - hybrid microcircu its, general specification for. standards department of defense mil-std-883 - test method standard microcircuits. mil-std-1835 - interface standard for microcircuit case outlines. handbooks department of defense mil-hdbk-103 - list of standard microcircuit drawings (smd's). mil-hdbk-780 - standard microcircuit drawings. (unless otherwise indicated, copies of the specificat ion, standards, and handbooks are ava ilable from the standardization document order desk, 700 robbins avenue, building 4d, philadelphia, pa 19111-5094.) 1 / stresses above the absolute maximum ratings may cause permanent damage to the device. extended operation at the maximum levels may degrade performance and affect reliability.
standard microcircuit drawing size a 5962-02510 defense supply center columbus columbus, ohio 43216-5000 revision level sheet 4 dscc form 2234 apr 97 2.2 order of precedence . in the event of a conflict between the text of th is drawing and the references cited herein, the text of this drawing takes precedence. nothing in this docum ent, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. requirements 3.1 item requirements . the individual item performance requirements fo r device classes d, e, g, h, and k shall be in accordance with mil-prf-38534. compliance with mil-prf- 38534 may include the performance of all tests herein or as designated in the device manufacturer's quality management (qm) plan or as designated for the applicable device class. therefore, the tests and inspections herein may not be per formed for the applicable device class (see mil-prf-38534). furthermore, the manufacturer may take ex ceptions or use alternate methods to the tests and inspections herein and not perform them. however, the performanc e requirements as defined in mil-prf-38534 shall be met for the applicable device class. 3.2 design, construction, and physical dimensions . the design, construction, and physica l dimensions shall be as specified in mil-prf-38534 and herein. 3.2.1 case outline(s) . the case outline(s) shall be in a ccordance with 1.2.4 herein and figure 1. 3.2.2 terminal connections . the terminal connections sha ll be as specified on figure 2. 3.3 electrical perfo rmance characteristics . unless otherwise specified herein, the electrical performance characteristics are as specified in table i and shall apply over the full specified operat ing temperature range. 3.4 electrical test requirements . the electrical test requirements shall be the subgroups specified in t able ii. the electrical tests for each subgroup are defined in table i. 3.5 marking of device(s) . marking of device(s) shall be in accordanc e with mil-prf-38534. the device shall be marked with the pin listed in 1.2 herein. in addition, the manufac turer's vendor similar pin may also be marked in mil-hdbk-103 and qml-38534. 3.6 data . in addition to the general performance requirements of mil-prf-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables fo rmat) from the initial quality c onformance inspection group a lot sample, for each device type listed herein. also, the data shoul d include a summary of all parameters manually tested, and for those which, if any, are guaranteed. this data shall be mainta ined under document revision level control by the manufacturer and be made available to the preparing activity (dscc-va) upon request. 3.7 certificate of compliance . a certificate of compliance shall be required fr om a manufacturer in or der to supply to this drawing. the certificate of compliance (o riginal copy) submitted to dscc-va shall a ffirm that the manufacturer's product meets the performance requirements of mil-prf-38534 and herein. 3.8 certificate of conformance . a certificate of conformance as required in mil-prf-38534 shall be provided with each lot of microcircuits delivered to this drawing.
standard microcircuit drawing size a 5962-02510 defense supply center columbus columbus, ohio 43216-5000 revision level sheet 5 dscc form 2234 apr 97 table i. electrical per formance characteristics . test symbol conditions 1 / -55 c t c +125 c v in = 28 v dc 0.5 v group a subgroups device types limits unit no external sync, c l = 0 unless otherwise specified min max 1 3.27 3.33 i out = 2.4 a dc 2,3 01,02 3.20 3.40 output voltage v out l, r 1,2,3 02 3.10 3.50 v dc v in = 16 v dc to 40 v dc 1,2,3 01, 02 2400 output current i out l, r 1,2,3 02 2400 ma 01 80 1 02 160 i out = 2.4 a bw = 10 khz to 2 mhz 2,3 01,02 240 v out ripple voltage v rip l, r 1,2,3 02 350 mvp-p v in =16 v dc to 40 v dc i out = 2.4 a 1,2,3 01,02 100 v out line regulation vr line l, r 1,2,3 02 200 mv i out = 0 to 2.4 a 1,2,3 01,02 50 v out load regulation vr load l, r 1,2,3 02 100 mv i out = 0 a, inhibit (pin 1) = 0 v dc 1,2,3 01,02 12 l, r 1,2,3 02 15 01 40 i out = 0 a, inhibit (pin 1) = open 1, 2, 3 02 65 input current i in l, r 1,2,3 02 100 ma 1 01,02 80 i out = 2.4 a, bw = 10 khz to 10 mhz 2,3 01,02 120 i in ripple current i rip l, r 1,2,3 02 150 map-p see footnotes at end of table.
standard microcircuit drawing size a 5962-02510 defense supply center columbus columbus, ohio 43216-5000 revision level sheet 6 dscc form 2234 apr 97 table i. electrical per formance characteristics - continued. test symbol conditions 1 / -55 c t c +125 c v in = 28 v dc 0.5 v group a subgroups device types limits unit no external sync, c l = 0 unless otherwise specified min max efficiency eff i out = 2.4 a 1 01,02 70 % 2,3 01,02 67 l, r 1,2,3 02 62 isolation iso input to output or any pin to case (except pin 6) at 500v dc, 1 01,02 100 m ? t c = +25 c l, r 1 02 100 short circuit power dissipation, p d p d = p in - total p out 1,2,3 01,02 8 w l, r 1,2,3 02 9 4 01,02 500 600 switching frequency f s i out = 2.4 a 5,6 01,02 480 620 khz l, r 4,5,6 02 400 700 external sync range 2 / f sync i out = 2.4 a, ttl level to pin 5 4,5,6 01,02 500 600 khz l, r 4,5,6 02 500 600 v out step load transient 3 / v tload 50% load to/from 100% load 4,5,6 01,02 -400 +400 mv pk l, r 4,5,6 02 -1200 +1200 v out step load transient recovery 3 / 4 / 5 / tt load 50% load to/from 100% load 4,5,6 01,02 300 s l, r 4,5,6 02 1200 v out step line transient 4 / 6 / v tline input step 16 v dc to/from 40 v dc, i out = 2.4 a 4,5,6 01,02 -800 +800 mv pk l, r 4,5,6 02 -1500 +1500 see footnotes at end of table.
standard microcircuit drawing size a 5962-02510 defense supply center columbus columbus, ohio 43216-5000 revision level sheet 7 dscc form 2234 apr 97 table i. electrical per formance characteristics - continued. test symbol conditions 1 / -55 c t c +125 c v in = 28 v dc 0.5 v group a subgroups device types limits unit no external sync, c l = 0 unless otherwise specified min max v out step line transient recovery 4 / 5 / tt line input step 16 v dc to/from 40 v dc, i out = 2.4 a 4,5,6 01,02 1.2 ms l, r 4,5,6 02 2.4 start up overshoot 4 / vton os i out = 2.4 a, v in = 0 to 28 v dc 4,5,6 01,02 300 mv pk l, r 4,5,6 02 1500 start up delay 7 / ton d i out = 2.4 a, v in = 0 to 28 v dc 4,5,6 01,02 25 ms l, r 4,5,6 02 100 load fault recovery 4 / tr lf i out = 2.4 a 4,5,6 01,02 30 ms l, r 4,5,6 02 100 capacitive load 4 / 8 / c l no effect on dc performance, t c = +25 c 4 01,02 300 f l, r 4 02 300 1 / post irradiation testing shall be in accordance with 4.3.5 herein. 2 / a ttl level waveform (v ih = 4.5 v minimum, v il = 0.8 v maximum) with a 50% 10% duty cycle applied to the sync input pin (pin 5) within the sync range fr equency shall cause the converter? s switching frequency to become synchronous with the frequency applied to the sync input pin (pin 5). 3 / load step transition time greater than 10 s. 4 / parameter shall be tested as part of device characte rization and after design and process changes. thereafter, parameters shall be guaranteed to t he limits specified in table i. 5 / recovery time is measured from t he initiation of the transient until v out has returned to within 1 percent of v out final value. 6 / input step transition time greater than 10 s. 7 / start up delay time measurement is eit her for a step application of power at the input or the removal of a ground signal from the inhibit pin (pin 1) while power is applied to the input. 8 / capacitive load may be any value from 0 to the maximum limit without compromising dc performance.
standard microcircuit drawing size a 5962-02510 defense supply center columbus columbus, ohio 43216-5000 revision level sheet 8 dscc form 2234 apr 97 case outline x. symbol millimeters inches min max min max a 8.38 .330 b 0.64 0.89 .025 .035 d 36.70 28.32 1.445 1.455 e 5.08 5.33 .200 .210 e1 12.08 12.95 .500 .510 e2 17.78 18.03 .700 .710 e3 22.86 23.11 .900 .910 e4 27.94 28.19 1.100 1.110 e 28.32 28.57 1.115 1.125 e1 20.19 20.44 .795 .805 l 6.09 6.60 .240 .260 notes: 1. the case outline x was originally designed us ing the inch-pound units of measurem ent, in the event of conflict between the metric and in ch-pound units, the inch-pound units shall take precedence. 2. pin numbers are for reference only. 3. device weight: 30 grams. figure 1. case outline(s) .
standard microcircuit drawing size a 5962-02510 defense supply center columbus columbus, ohio 43216-5000 revision level sheet 9 dscc form 2234 apr 97 case outline z. symbol millimeters inches min max min max a 8.38 .330 a1 0.94 1.45 .037 .057 b 0.64 0.89 .025 .035 d 50.80 2.000 d1 43.82 44.07 1.725 1.735 d2 36.83 1.450 e 8.64 8.89 .340 .350 e1 16.26 16.51 .640 .650 e2 21.37 21.59 .840 .850 e3 26.41 26.67 1.040 1.050 e4 31.50 31.75 1.240 1.250 e 28.70 1.130 e1 20.07 20.57 .790 .810 l 6.09 6.60 .240 .260
standard microcircuit drawing size a 5962-02510 defense supply center columbus columbus, ohio 43216-5000 revision level sheet 10 dscc form 2234 apr 97 device types 01 and 02 case outlines x and z terminal number terminal symbol 1 inhibit 2 no connection 3 output return 4 output 5 sync input 6 case ground 7 input return 8 input figure 2. terminal connections .
standard microcircuit drawing size a 5962-02510 defense supply center columbus columbus, ohio 43216-5000 revision level sheet 11 dscc form 2234 apr 97 4. quality assurance provisions 4.1 sampling and inspection . sampling and inspection procedures shall be in accordance with mil-prf-38534 or as modified in the device manufacturer's quality management (qm) pl an. the modification in the qm plan shall not affect the form, fit, or function as described herein. 4.2 screening . screening shall be in accordance with mil-prf- 38534. the following additional criteria shall apply: a. burn-in test, method 1015 of mil-std-883. (1) test condition a, b, c, or d. the test circuit sha ll be maintained by the manufacturer under document revision level control and shall be made available to either dscc-va or t he acquiring activity upon request. also, the test circuit shall specify the inputs, outputs, biases, and power dissi pation, as applicable, in accordance with the intent specified in test method 1015 of mil-std-883. (2) t a as specified in accordance with table i of method 1015 of mil-std-883. b. interim and final electrical test parameters shall be as spec ified in table ii herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. table ii. electrical test requirements . mil-prf-38534 test requirements subgroups (in accordance with mil-prf-38534, group a test table) interim electrical parameters final electrical parameters 1*, 2, 3, 4, 5, 6 group a test requirements 1, 2, 3, 4, 5, 6 group c end-point electrical parameters 1 end-point electrical parameters for radiation hardness assurance (rha) devices 1, 2, 3, 4, 5, 6 * pda applies to subgroup 1. 4.3 conformance and periodic inspections . conformance inspection (ci) and periodi c inspection (pi) shall be in accordance with mil-prf-38534 and as specified herein. 4.3.1 group a inspection (ci) . group a inspection shall be in accordance with mil-prf-38534 and as follows: a. tests shall be as specified in table ii herein. b. subgroups 7, 8, 9, 10, and 11 shall be omitted. 4.3.2 group b inspection (pi) . group b inspection shall be in accordance with mil-prf-38534.
standard microcircuit drawing size a 5962-02510 defense supply center columbus columbus, ohio 43216-5000 revision level sheet 12 dscc form 2234 apr 97 4.3.3 group c inspection (pi) . group c inspection shall be in accordance with mil-prf-38534 and as follows: a. end-point electrical parameters shall be as specified in table ii herein. b. steady-state life test, method 1005 of mil-std-883. (1) test condition a, b, c, or d. the test circuit sha ll be maintained by the manufacturer under document revision level control and shall be made available to either dscc-va or t he acquiring activity upon request. also, the test circuit shall specify the inputs, outputs, biases, and power dissi pation, as applicable, in accordance with the intent specified in test method 1005 of mil-std-883. (2) t a as specified in accordance with table i of method 1005 of mil-std-883. (3) test duration: 1,000 hours, except as permitted by method 1005 of mil-std-883. 4.3.4 group d inspection (pi) . group d inspection shall be in accordance with mil-prf-38534. 4.3.5. radiation hardness assurance (rha). rha qualification is required only for t hose devices with the rha designator as specified herein. rha level l rha level r units total ionizing dose tolerance level 50 100 krad (si) single event upset survival level (let) no guarantee 40 mev a. radiation dose rate is in accordance with condition c of method 1019 of mil-std-883. unless otherwise specified, components are tested at a rate of 9 rad(si)/s, in acco rdance with method 1019 of mil-std-750 or mil-std-883, as applicable. b. the manufacturer shall perform a worst-case and radiati on susceptibility analysis on the device. this analysis shall show that the minimum performance requirements of each component has adequate design margin under worst-case operating conditions (extremes of line voltage, temperatur es, load, frequency, radiation environment, etc.). this analysis guarantees the post-irradiation parameter limits specified in table i. c. rha testing shall be performed at the component level fo r initial device qualification, and after design changes that may affect the rha performance of the device. as an alternative to testing, components may be procured to manufacturer radiation guarantees that meet the mini mum performance requirements. component radiation performance guarantees shall be established in complianc e with mil-prf-19500, group d or mil-prf-38535, group e, as applicable. for components with less than adequate performance margin, component lot radiation acceptance screening shall be performed. d. the manufacturer shall establish pr ocedures controlling component radiation test ing, and shall establish radiation test plans used to implement component lot qualification during pr ocurement. test plans and test reports shall be filed and controlled in accordance with the manufac turer's configuration management system. e. the device manufacturer shall designate a rha program manager to oversee component lot qualification, and to monitor design changes for continued co mpliance to rha requirements.
standard microcircuit drawing size a 5962-02510 defense supply center columbus columbus, ohio 43216-5000 revision level sheet 13 dscc form 2234 apr 97 5. packaging 5.1 packaging requirements . the requirements for packaging shall be in accordance with mil-prf-38534. 6. notes 6.1 intended use . microcircuits conforming to this drawing are intended for use for gove rnment microcircuit applications (original equipment), design applic ations, and logistics purposes. 6.2 replaceability . microcircuits covered by this drawing will repl ace the same generic device covered by a contractor- prepared specification or drawing. 6.3 configuration control of smd's . all proposed changes to existing smd's will be coordinated with the users of record for the individual documents. this coordination w ill be accomplished in accordance with mil-prf-38534. 6.4 record of users . military and industrial users shall inform defens e supply center columbus when a system application requires configuration control and the applicable smd. dscc w ill maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. us ers of drawings covering micr oelectronic devices (fsc 5962) should contact dscc-va, telephone (614) 692-0544. 6.5 comments . comments on this drawing should be directed to dscc-va, post office box 3990, columbus, ohio 43216- 5000, or telephone (614) 692-0512. 6.6 sources of supply . sources of supply are listed in mil-hdbk- 103 and qml-38534. the vendors listed in mil-hdbk- 103 and qml-38534 have submitted a certificate of compliance (s ee 3.7 herein) to dscc-va and have agreed to this drawing.
standard microcircuit drawing bulletin date: 01-11-30 approved sources of supply for smd 5962-02510 are listed below for immediate acquisition information only and shall be added to mil-hdbk-103 and qml-38534 during the next revisions. mil-hdbk-103 and qml-38534 will be revised to include the addition or deletion of sources. the vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accept ed by dscc-va. this bulletin is superseded by the next dated revisions of mil-hdbk-103 and qml-38534. standard microcircuit drawing pin 1 / vendor cage number vendor similar pin 2 / 5962-0251001hxa 5962-0251001hxc 5962-0251001hza 5962-0251001hzc 50821 50821 50821 50821 mhf+283r3s/883 mhf+283r3s/883 mhf+283r3sf/883 mhf+283r3sf/883 5962-0251002hxa 5962-0251002hxc 5962-0251002hza 5962-0251002hzc 50821 50821 50821 50821 smhf283r3s/ho smhf283r3s/ho smhf283r3sf/ho smhf283r3sf/ho 5962l0251002hxa 5962l0251002hxc 5962l0251002hza 5962l0251002hzc 50821 50821 50821 50821 smhf283r3s/hl smhf283r3s/hl smhf283r3sf/hl smhf283r3sf/hl 5962R0251002HXA 5962r0251002hxc 5962r0251002hza 5962r0251002hzc 50821 50821 50821 50821 smhf283r3s/hr smhf283r3s/hr smhf283r3sf/hr smhf283r3sf/hr 5962l0251002kxa 5962l0251002kxc 5962l0251002kza 5962l0251002kzc 50821 50821 50821 50821 smhf283r3s/kl smhf283r3s/kl smhf283r3sf/kl smhf283r3sf/kl 5962r0251002kxa 5962r0251002kxc 5962r0251002kza 5962r0251002kzc 50821 50821 50821 50821 smhf283r3s/kr smhf283r3s/kr smhf283r3sf/kr smhf283r3sf/kr 1 / the lead finish shown for each pin representing a herme tic package is the most readily available from the manufacturer listed for that part. if the desired lead fini sh is not listed contact t he vendor to determine its availability. 2 / caution . do not use this number for it em acquisition. items acquired to this number may not satisfy the performance requirements of this drawing. vendor cage vendor name number and address 50821 interpoint corporation 10301 willows road redmond, wa 98073-9705 the information contained herein is disseminated for convenience only and the government assumes no liability whatsoever for any inaccuracies in the information bulletin.

▲Up To Search▲

Price & Availability of 5962R0251002HXA

	To Download 5962R0251002HXA Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .